Thursday, December 23, 2010

Temperature-controlled 12V dc Fan

Temperature-controlled 12V dc Fan

Parts:

R1______________15K  @ 20°C n.t.c. Thermistor (See Notes)
R2_______________1K5 1/4W Resistor (See Notes)
R3_______________1K  1/4W Resistor
R4_____________270R  1/4W Resistor
R5______________22K  1/2W Trimmer Cermet or Carbon
R6_____________680R  1/4W Resistor (Optional, see Notes)
R7_____________470R  1/2W Trimmer Cermet or Carbon (Optional, see Notes)

C1_____________100µF  25V Electrolytic Capacitor

D1______________LED   (Optional, any shape and color, see Notes)

Q1____________BC547   45V 100mA NPN Transistor
Q2____________BD140   80V 1.5A PNP Transistor

M1____________Fan Motor 12V 700mA max.

Comments:

Requested by some correspondents, this simple design allows an accurate speed control of 12V dc fan motors, proportional to temperature.
A n.t.c. Thermistor (R1) is used as temperature sensor, driving two directly coupled complementary transistors wired in a dc feedback circuit.
An optional circuitry was added to remotely monitor fan operation and to allow some sort of rough speed indication by means of the increasing brightness of a LED.

Notes:

  • R5 must be set to allow motor just starting at the desired temperature.
  • Any n.t.c. Thermistor in the 6K8 - 22K range value might work, provided R2 value is one/tenth of Thermistor's value.
  • R6, R7 and D1 are optional: R7 must be adjusted until the LED glows faintly when the motor is just running.

Room Noise Detector

circuit diagram:

Noise Detector circuit diagram

Parts:

R1____________10K   1/4W Resistor
R2,R3_________22K   1/4W Resistors
R4___________100K   1/4W Resistor
R5,R9,R10_____56K   1/4W Resistors
R6_____________5K6  1/4W Resistor
R7___________560R   1/4W Resistor
R8_____________2K2  1/4W Resistor
R11____________1K   1/4W Resistor
R12___________33K   1/4W Resistor
R13__________330R   1/4W Resistor

C1___________100nF  63V Polyester Capacitor
C2____________10µF  25V Electrolytic Capacitor
C3___________470µF  25V Electrolytic Capacitor
C4____________47µF  25V Electrolytic Capacitor

D1_____________5mm. Red LED

IC1__________LM358  Low Power Dual Op-amp

Q1___________BC327  45V 800mA PNP Transistor

MIC1_________Miniature electret microphone

SW1__________2 poles 4 ways rotary switch

B1___________9V PP3 Battery

Clip for PP3 Battery

Device purpose:

This circuit is intended to signal, through a flashing LED, the exceeding of a fixed threshold in room noise, chosen from three fixed levels, namely 50, 70 & 85 dB. Two Op-amps provide the necessary circuit gain for sounds picked-up by a miniature electret microphone to drive a LED. With SW1 in the first position the circuit is off. Second, third and fourth positions power the circuit and set the input sensitivity threshold to 85, 70 & 50 dB respectively.
Current drawing is <1mA with LED off and 12-15mA when the LED is steady on.

Use:

  • Place the small box containing the circuit in the room where you intend to measure ambient noise.
  • The 50 dB setting is provided to monitor the noise in the bedroom at night. If the LED is steady on, or flashes bright often, then your bedroom is inadequate and too noisy for sleep.
  • The 70 dB setting is for living-rooms. If this level is often exceeded during the day, your apartment is rather uncomfortable.
  • If noise level is constantly over 85 dB, 8 hours a day, then you are living in a dangerous environment.

dBExample of sound sources
20Quiet garden, electric-clock ticking, drizzling rain
30Blast of wind, whisper @ 1 m.
40Countryside areas, quiet apartment, wrinkling paper @ 1 m.
50Residential areas, quiet streets, fridges, conversation @ 1 m.
55Offices, air-conditioners
60Alarm-clocks, radio & TV sets at normal volume
64Washing machines, quiet typewriters
67Hair-dryers, crowded restaurants
69Dish-washers, floor-polishers
70Loud conversation, noisy street, radio & TV sets at high volume
72Vacuum cleaners
78Telephone ring, mechanical workshop
80Passing trucks, noisy hall or plant, shuffling @ 1 m.
90Passing train, pneumatic hammer, car hooter @ 1 m.
95Mega "disco", circular saw
100Motorcycle without silencer

Nocturnal Animals Whisker

Animals Whisker

Parts:

R1____________100K   1/4W Resistor
R2______________2M2  1/4W Resistor
R3_____________10K   1/4W Resistor (see Notes)
R4______________4K7  1/4W Resistor
R5____________Photo resistor (any type, see Notes)

C1,C2,C3_______47µF  25V Electrolytic Capacitors

D1___________1N4148  75V 150mA Diode

IC1____________7555 or TS555CN CMos Timer IC

Q1____________BD681  100V 4A NPN Darlington Transistor

LP1____________6V 3W Bulb (see Notes)

SW1____________SPST Switch

B1_____________6V 1.2A Lead acid sealed rechargeable Battery (see Notes)

Device purpose:

This circuit has proved very useful in keeping away from a terrace or a porch some bats and other nocturnal animals. You can use it for similar or different purposes. The lamp illuminates for a 4-5 seconds delay and stays off about one minute and 15 seconds. The photo resistor allows automatic switch-on of the circuit at dusk and switch-off at dawn. Supposing an eight hours operation per night, the lamp stays on for a total of about 30 minutes, allowing great current economy.

Circuit operation:

IC1 is wired as an astable multivibrator with on and off time-delays as explained before. R1 & C1 set the on time-delay, R2 & C1 set the off time-delay. As there is no critical parameter, you can set these delays at your wish. Q1 is the lamp driver and can feed rather big bulbs. C2 prevents some brief instability when voltage at pin 4 of IC1 is very close to switching threshold.

Notes:

  • Mount the photo resistor's sensitive surface at an angle of 90 degrees or more compared with the lamp, in order to avoid light interaction.
  • Owing to the photo resistor type or to suit your own special needs, R3 can be varied to set the operating threshold.
  • If you are not needing automatic on-off operation, omit R3 & R5 and connect pin 4 of IC1 to positive supply.
  • The bulb can be any 6V type up to 10-12W, but a 3W one is a very good compromise.
  • Batteries can be of the rechargeable type: lead acid sealed, NI-CD, NI-MH packages ranging from 3.6 to 12V, making sure that suitable bulbs are provided.
  • Using 1.2 Ampere-hour batteries, you should probably recharge them once a week or less.
  • Obviously you can feed permanently the circuit by means of a suitable mains power supply.

Blinking Arrow



Blinking Arrow

Parts:

R1_____________500K  1/2W Trimmer
R2______________22K  1/4W Resistor
R3,R5,R7,R9_____10K  1/4W Resistors
R4,R6,R8,R10_____4K7 1/4W Resistors
R11,R12,R13____470R  1/4W Resistors
R14____________270R  1/4W Resistor

C1_______________4µ7  25V Electrolytic Capacitor
C2_____________220µF  25V Electrolytic Capacitor

D1--D17________LEDs   Any type and color (except blue and white, see Notes)

Q1,Q2,Q3,Q4___BC337   45V 800mA NPN Transistor

IC1____________4093   Quad 2 input Schmitt NAND Gate IC
IC2____________4520   Dual binary up-counter IC
IC3____________4094   8-stage shift-and-store bus register IC


Comments:

A blinking arrow can be a very attractive gadget, suitable for many indication purposes. This circuit provides a bar-mode sequencer driving 17 LEDs arranged in four groups in order to build-up a bright arrow. When the build-up of the arrow is completed, all LEDs stay on for some time, then off for the same time-delay and then the cycle restarts. Sequence speed can be set by R1.
For those wishing to experiment, sequence timings can also be varied by connecting pin #5 of IC1B to pin #5 of IC2 and pins #6, 8 and 9 of IC1 to pin #6 of IC2. Other pin combinations are possibile by shifting the above named pins of IC1 to higher outputs of the counters contained in IC2, i.e. pins #6 and 11, pins #11 and 12 etc.
The resulting effect of the original four groups of 17 LEDs arrangement is shown in the title heading.

Notes:

  • Obviously, many different arrangements using more or less LEDs are possibile.
  • At 12V supply the maximum number of LEDs per strip is that shown in the circuit diagram, when red LED types are used. Yellow, green and orange types may require a lower value of the limiting resistors or a lesser number of devices per strip.
  • Please note that the unused section of IC1 must have the inputs tied to negative ground whereas the output must be left open, as shown at the bottom of the diagram.

Self-powered Door-bell Watcher

Door-bell Watcher

Parts:

R1______________1K   1/4W Resistor
R2____________220K   1/4W Resistor (Optional, see text)
R3______________2K2  1/4W Resistor (Optional, see text)

C1___________1000µF   25V Electrolytic Capacitor (See Notes)
C2____________100nF  400V Polyester Capacitor (Optional, see text)

D1__________1N4002   100V 1A Diode
D2_____________5mm. Red LED

P1_____________SPST Pushbutton

BZ1___________Piezo sounder (incorporating 3KHz oscillator) (Optional, see text)

Comments:

This very simple and self-powered device was conceived to allow a person to monitor if someone has rung his home door-bell when he was out.
As most door-bells use 12Vac supply, the circuit must be simply connected to the two door-bell-coil leads.
When the door-bell is activated, an ac voltage of about 10 - 16V is developed at its leads, so it is rectified by D1 and charges C1.
Though this device was primarily intended to be used when a person leaves the house for a few hours or a week-end, a number of tests has proven that a minimum of 15 days "memory" can be guaranteed, even using cheap capacitor types.
To know if the door-bell has rung, you must simply push P1: if the event occurred, LED D2 will illuminate and will fade slowly to the off-state in some seconds. This operation will reset the circuit also.
The LED can be substituted or supported by a small Piezo sounder (incorporating 3KHz oscillator)
A small number of door-bells powered by 230 or 115Vac can be found. In this case, R2, R3 and C2 must be added to the input of the basic circuit, allowing about 15Vac to develop across R3, the voltage-drop provided by C2 reactance.
The mains supply operation facility, allows further development of the circuit purposes.
In fact, almost any mains supplied apparatus can be monitored, e.g. household appliances, computers, radio and television sets, Hi-Fi systems, lamps etc., provided the circuit can be inserted after the main on-off switch.

Notes:

  • The added high-voltage circuit formed by R2, R3 and C2 was designed for 230Vac operation. If your ac mains is rated at about 115V, you must change C2 value to 220nF 250V. No other changes are required.
  • In most cases, a 470µF 25V value for C1 would suffice.
  • Warning! If the circuit is connected to 230Vac mains, some parts in the circuit board can be subjected to lethal potential! Avoid touching the circuit when plugged and enclose it in a plastic box.

Programmable LED Flashers

Programmable LED Flasher #1

Parts:

R1______________10K  1/4W Resistor
R2_______________1M  1/4W Resistor
R3_______________1K  1/4W Resistor (See Notes)

C1_______________4µ7  25V Electrolytic Capacitor
C2______________10nF  63V Polyester Capacitor

D1___________1N4148   75V 150mA Diode
D2______________LED (Any dimension, shape or color)

IC1____________4060  14 stage ripple counter and oscillator IC

P1_____________SPST  Pushbutton
SW1____________SPST  Toggle or Slider Switch

B1______________3V to 15V Battery or dc power source (See Notes)
Programmable LED Flasher #2

Parts:

R1_____________100K  1/4W Resistor
R2_______________1K  1/4W Resistor (See Notes)
R3______________10K  1/4W Resistor

C1,C2____________4µ7  25V Electrolytic Capacitors

D1___________1N4148   75V 150mA Diode
D2______________LED (Any dimension, shape or color)

IC1____________7555 or TS555CN CMos Timer IC
IC3____________4017  Decade counter with 10 decoded outputs IC

SW1____________1 pole 9 ways Rotary Switch (Optional)
SW2____________SPST  Toggle or Slider Switch

B1______________3V to 15V Battery or dc power source (See Notes)

Comments:

These circuits were designed on request. Both feature a flashing LED that, after a preset number of flashes will illuminate steadily until P1 (Reset) will be pressed.
Circuit #1 uses only one chip and can be useful if a not very precise number of flashes of the LED is needed before reverting to the steady-on state. In fact, connecting D1 Anode to different output pins of the IC, the steady-on state of the LED will be obtained after 2, 4, 8, 16 flashes and so on.
Connecting D1 Anode as shown, the LED will start flashing at about two times per second after power-on and will revert to the steady state after 8 flashes. P1 resets the circuit and C1 automatically resets IC at power-on.
Connecting D1 Anode to pin #13 of IC1 the flashes will be 4; to pin #1 will be 16 etc.
The flashing frequency of the LED can be varied by changing the values of R2 and/or C2.
Circuit #2 is more precise and uses about the same parts count of Circuit #1, though requiring two ICs. By choosing the appropriate output pin of IC2, the steady-on state of the LED will be obtained after 1 to 9 flashes, as shown in the drawing at SW1 pins. This switch is optional, as D1 Anode can be hard wired directly to the required output pin of IC2. P1 will work as in Circuit #1 but with some difference: after a momentarily press the LED will restart to flash, but the total number of flashes will be one less than obtained after power-on. Furthermore, if P1 is closed permanently, the circuit will flash permanently.
The flashing frequency of the LED can be varied by changing R1 and/or C1 values.

Notes:

  • Circuits were tested at 9V supply, but they might work in the 3 - 15V dc supply range.
  • The LED current limiting resistor value was calculated for 9 - 12V supply and should be changed to suit different supply voltages.

Dancing LEDs

Dancing LEDs

Parts:

R1_____________10K   1/4W Resistor
R2,R3__________47K   1/4W Resistors
R4______________1K   1/4W Resistor
R5,R6,R7______100K   1/4W Resistors
R8____________820R   1/4W Resistor

C1,C3_________100nF   63V Ceramic or Polyester Capacitors
C2_____________10µF   50V Electrolytic Capacitor
C4____________330nF   63V Polyester Capacitor (See Notes)
C5____________100µF   25V Electrolytic Capacitor

D1___________1N4148   75V 150mA Diode
D2-D11_________5 or 3mm. LEDs (any type and color)

IC1___________LM358  Low Power Dual Op-amp
IC2____________4017  Decade counter with 10 decoded outputs IC

M1_____________Miniature electret microphone

SW1____________SPST  miniature Slider Switch

B1_______________9V  PP3 Battery

Clip for PP3 Battery

Additional circuit parts (see Notes):

R9,R10_________10K   1/4W Resistors
R11____________56R   1/4W Resistor

D12,D13 etc.____5 or 3mm. LEDs (any type and color)

Q1,Q2_________BC327   45V 800mA PNP Transistors
Q3____________BC337   45V 800mA NPN Transistor


Device purpose:

The basic circuit illuminates up to ten LEDs in sequence, following the rhythm of music or speech picked-up by a small microphone. The expanded version can drive up to ten strips, formed by up to five LEDs each, at 9V supply.

Circuit operation:

IC1A amplifies about 100 times the audio signal picked-up by the microphone and drives IC1B acting as peak-voltage detector. Its output peaks are synchronous with the peaks of the input signal and clock IC2, a ring decade counter capable of driving up to ten LEDs in sequence.
An additional circuit allows the driving of up to ten strips, made up by five LEDs each (max.), at 9V supply. It is formed by a 10mA constant current source (Q1 & Q2) common to all LED strips and by a switching transistor (Q3), driving a strip obtained from 2 to 5 series-connected LEDs. Therefore one transistor and its Base resistor are required to drive each of the strips used.

Notes:

  • The sensitivity of the circuit can be varied changing R4 value.
  • C4 value can be varied from 220 to 470nF in order to change the circuit speed-response to music peaks.
  • Adopting the additional circuit, only one item for R10, R11, Q1 and Q2 is required to drive up to ten LED strips. On the contrary, one item of R9 and Q3 is necessary to drive each of the strips you decided to use.
  • Each R9 input must be connected to IC2 output pins, in place of the LEDs D2-D11 shown. R8 must also be omitted.
  • Whishing to use a lower number of LEDs or LED strips, pin #15 of IC2 must be disconnected from ground and connected to the first unused output pin.
    For example: if you decided to use 5 LEDs, pin #15 of IC2 must be connected to pin #1; if you decided to use 8 LEDs, pin #15 of IC2 must be connected to pin #9 etc.
  • Current drawing of the circuit is about 10mA.
  • Whishing to use a wall-plug adapter instead of a 9V battery, you can supply the circuit at 12V, allowing the use of up to 6 LEDs per strip, or at 15V, allowing the use of up to 7 LEDs per strip.